A resistor ladder between power and ground is used to generate 15 reference voltages at regular intervals. The input signal is compared with each of them in turn to get a unary ADC output. To avoid loading the input too much, some voltage followers are added before the comparators. Finally, a digital encoder circuit with error correction converts the unary output to binary using a tree of majority gates and multiplexers. The digital circuit also implements some debugging logic.
For basic operation, set the first two digital inputs to 0 and apply a voltage between 0 and 1.8 V to the analog input pin. The first four output pins should give a binary readout.
The second set of four output pins samples the unary output at bits 1, 5, 9 and 13 to indicate if the input voltage is over the reference voltages 0.18 V, 0.66 V, 1.14 V and 1.62 V respectively.
Bidirectional pins are configured as outputs where the first four is an XOR of some unary pins and the second four multiplexes unary pins using input pins 2 and 3 as a selector. Both features allow checking when the input signal crosses one of the intermediate reference thresholds.
| Input range | Unary | Binary | Sample | XOR | Mux00 | Mux01 | Mux10 | Mux11 |
|---|---|---|---|---|---|---|---|---|
| 0 V to 0.06 V | 000000000000000 | 0000 | 0000 | 0000 | 0000 | 0000 | 0000 | 0000 |
| 0.06 V to 0.18 V | 000000000000001 | 0001 | 0000 | 0001 | 0001 | 0000 | 0000 | 0000 |
| 0.18 V to 0.3 V | 000000000000011 | 0010 | 0001 | 0011 | 0011 | 0000 | 0000 | 0000 |
| 0.3 V to 0.42 V | 000000000000111 | 0011 | 0001 | 0111 | 0111 | 0000 | 0000 | 0000 |
| 0.42 V to 0.54 V | 000000000001111 | 0100 | 0001 | 1111 | 1111 | 0000 | 0000 | 0000 |
| 0.54 V to 0.66 V | 000000000011111 | 0101 | 0001 | 1110 | 1111 | 0001 | 0000 | 0000 |
| 0.66 V to 0.78 V | 000000000111111 | 0110 | 0011 | 1100 | 1111 | 0011 | 0000 | 0000 |
| 0.78 V to 0.9 V | 000000001111111 | 0111 | 0011 | 1000 | 1111 | 0111 | 0000 | 0000 |
| 0.9 V to 1.02 V | 000000011111111 | 1000 | 0011 | 0000 | 1111 | 1111 | 0000 | 0000 |
| 1.02 V to 1.14 V | 000000111111111 | 1001 | 0011 | 0001 | 1111 | 1111 | 0001 | 0000 |
| 1.14 V to 1.26 V | 000001111111111 | 1010 | 0111 | 0011 | 1111 | 1111 | 0011 | 0000 |
| 1.26 V to 1.38 V | 000011111111111 | 1011 | 0111 | 0111 | 1111 | 1111 | 0111 | 0000 |
| 1.38 V to 1.5 V | 000111111111111 | 1100 | 0111 | 1111 | 1111 | 1111 | 1111 | 0000 |
| 1.5 V to 1.62 V | 001111111111111 | 1101 | 0111 | 1110 | 1111 | 1111 | 1111 | 0001 |
| 1.62 V to 1.74 V | 011111111111111 | 1110 | 1111 | 1100 | 1111 | 1111 | 1111 | 0011 |
| 1.74 V to 1.8 V | 111111111111111 | 1111 | 1111 | 1000 | 1111 | 1111 | 1111 | 0111 |
The circuit also provides debug functionality to independently check the ADC and the encoder.
If the first input pin is set to 1, the circuit is in encoder debug mode where the rest of the input pins as well as the bidirectional pins (which are now turned into inputs) are used instead of the ADC. The output pins function as described above, the bidirectional pins obviously cannot provide output in this case.
Otherwise, if the second input pin is set to 1, the circuit is in ADC debug mode where the raw unary output from the ADC is directly sent to the output and bidirectional pins.
You can use your favourite microcontroller to generate an analog input by outputting a PWM signal and adding an external capacitor to ground that together with the microcontroller’s built-in resistance makes a simple low-pass RC filter.
| # | Input | Output | Bidirectional |
|---|---|---|---|
| 0 | debug encoder (skip ADC) | binary bit 0 | xor of unary bits 0, 4, 8, 12 |
| 1 | debug ADC (skip encoder) | binary bit 1 | xor of unary bits 1, 5, 9, 13 |
| 2 | unary selector bit 0 | binary bit 2 | xor of unary bits 2, 6, 10, 14 |
| 3 | unary selector bit 1 | binary bit 3 | xor of unary bits 3, 7, 11 |
| 4 | (debug mode only) | unary bit 1 | unary bit 4*sel |
| 5 | (debug mode only) | unary bit 5 | unary bit 4*sel+1 |
| 6 | (debug mode only) | unary bit 9 | unary bit 4*sel+2 |
| 7 | (debug mode only) | unary bit 13 | unary bit 4*sel+3 |
ua# |
analog# |
Description |
|---|---|---|
| 0 | 0 | ADC input |